Products Center
- S/SH type single stage double suction axially split diesel engine pump
- D series horizontal multistage centrifugal diesel engine pump
- HW mixed flow volute diesel engine pump
- SN type horizontal double suction axially split diesel engine pump
- Mobile diesel engine water pump
- ZX, ZW series self-priming diesel engine pump
- Stationary horizontal centrifugal diesel engine pump
Get a quote
High Lift Submersible Pump
- Flow: 10-1400m3/h
- Lift： 12-465m
- Diameter： 7 8 10 12 14 inch
- Power： 7.5-410kw
Product Detail
High Lift Submersible Pump widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities.
High Lift Submersible Pump Material:
Impeller: Cast iron HT200,or stainless steel
Pump bowl: Cast iron HT200,or stainless steel,such as ss304 ss316
Pump shaft : Cold-drawn steel with chrome plating,or stainless steel ss304 ss316
Motor Seal: Rubber O-ring seal,mechanical seal
Motor regulating sleeve: rubber
High Lift Submersible Pumps Parameters:
| Diameter | Model | Power | Flow range | Head range | |
| Inch(“) | QJ series | kw | hp | m3/h | m |
| 8″ | 200QJ15-81/6 | 7.5 | 10 | 13-17 | 68-92 |
| 8″ | 200QJ20-148/11 | 15 | 20 | 18-22 | 126-170 |
| 8″ | 200QJ20-175/13 | 18.5 | 25 | 18-22 | 150-210 |
| 8″ | 200QJ20-202/15 | 22 | 30 | 18-22 | 172-232 |
| 8″ | 200QJ20-243/18 | 25 | 35 | 18-22 | 206-280 |
| 8″ | 200QJ20-283/21 | 30 | 40 | 18-22 | 240-325 |
| 8″ | 200QJ20-338/25 | 37 | 50 | 18-22 | 287-388 |
| 8″ | 200QJ20-405/30 | 45 | 60 | 18-22 | 345-465 |
| 8″ | 200QJ25-56/4 | 7.5 | 10 | 23-27 | 45-67 |
| 8″ | 200QJ25-70/5 | 9.2 | 13 | 23-27 | 56-84 |
| 8″ | 200QJ25-98/7 | 11 | 15 | 23-27 | 84-112 |
| 8″ | 200QJ25-126/9 | 15 | 20 | 23-27 | 100-145 |
| 8″ | 200QJ25-154/11 | 18.5 | 25 | 23-27 | 138-184 |
| 8″ | 200QJ25-182/13 | 22 | 30 | 23-27 | 150-210 |
| 8″ | 200QJ25-224/16 | 30 | 40 | 23-27 | 190-258 |
| 8″ | 200QJ25-294/21 | 37 | 50 | 23-27 | 250-340 |
| 8″ | 200QJ32-128/8 | 22 | 30 | 29-35 | 106-150 |
| 8″ | 200QJ50-65/5 | 15 | 25 | 46-54 | 52-78 |
| 8″ | 200QJ63-126/9 | 37 | 50 | 58-68 | 100-147 |
| 8″ | 200QJ100-90/6 | 45 | 60 | 80-120 | 88-92 |
| 10″ | 250QJ50-140/7 | 30 | 40 | 46-54 | 119-161 |
| 10″ | 250QJ50-340/17 | 75 | 100 | 46-54 | 315-375 |
| 10″ | 250QJ80-220/11 | 90 | 120 | 74-86 | 190-250 |
| 10″ | 250QJ100-216/12 | 100 | 135 | 80-120 | 190-252 |
| 10″ | 250QJ125-192/12 | 110 | 150 | 113-134 | 163-220 |
| 10″ | 250QJ140-180/12 | 125 | 170 | 130-145 | 156-205 |
| 12″ | 300QJ200-40/2 | 37 | 50 | 186-214 | 35-45 |
| 12″ | 300QJ300-80/4 | 110 | 150 | 279-321 | 68-92 |
| 12″ | 300QJ400-120/3 | 220 | 300 | 368-432 | 117-123 |
| 12″ | 300QJ500-60/4 | 140 | 190 | 460-540 | 57-63 |
| 14″ | 350QJ250-25/1 | 30 | 40 | 233-267 | 22-28 |
| 14″ | 350QJ320-120/4 | 185 | 250 | 305-335 | 115-125 |
| 16″ | 400QJ500-40/1 | 90 | 120 | 460-540 | 38-42 |
| 16″ | 400QJ500-20/1 | 45 | 60 | 460-540 | 18-22 |
| 18″ | 450QJ1000-16/1 | 90 | 120 | 900-1200 | 12-20 |
| 20″ | 500QJ640-84/3 | 260 | 350 | 600-680 | 82-86 |
| 22″ | 550QJ1200-18/1 | 110 | 150 | 1100-1400 | 15-22 |
| 24″ | 600QJ800-50/2 | 220 | 300 | 750-850 | 48-52 |
| 24″ | 600QJ1000-60/3 | 300 | 400 | 900-1200 | 58-62 |
Submersible Pumps Working Conditions:
- Three-phase power supply, voltage 380V (error less than 5%), frequency 50Hz (error less than 1%).
- Motor must be filled with clean water.
- The primary impeller of the pump should be immersed at least 2m under dynamic water level. The pump unit shall be less than 70m deep under static water level. The foot of motor shall be at least 3m above well bottom.
- Water temperature no higher than 20 ℃.
- Sand content of the water (by quality) not more than 0.01%.
- Water PH 6.5~8.5.
- The content of hydrogen sulfide in water not more than 1.5 mg/l.
- The content of chloridion in water shall not be higher than 400mg/l.
- The water source shall provide enough water for the pump to work continuously
Product process：
